Rocket Giotto Service Manual

10Technical DataBrewing groups: 1Hot steam wands: 1Hot water wands: 1Coffee portion control: ManualBoiler water level control: AutomaticVolt

11Start upParts which can become hot and cause injuries. Caution!Never touch the following parts. They are or can become hot and could cause burns:1.

12We assume the machine is properly installedBefore starting using the machine, please control the following: (A)1. Lever (A-9) is

13Now please proceed as follows: (A) (B)1. Remove the cover from the water reservoir Fig. B-22. Remove the wat

145. Put on the cover on top of the water reservoir.6. Plug in the machine.7. Turn the on/off switch (A-4) to the on position “1” and open the steam

15Operating InstructionsThe below shown components are supplied with your machine (the one cup filter holder comes typically on special order)(A) Tamp

16Preparing one or two cups of espresso. For the correct espresso preparation technique see page 30Preparing a single espresso 25ml1. Use one cup fil

17Preparing TWO cups or a double espresso coffee. 50 to 60 mls.1. Use the two cup filter handle (with 2 spouts)2. Position the metal two cups filter

18Dispensing steam to froth or heat up liquids1. Fill a suitable ideally stainless steel pitcher (used for food only) with an insulated grip with th

195. When enough foam is achieved, submerge nozzle (going sidewise) and keep it in that position finishing heating milk until the pitcher is too warm

2ContentsGeneral data 3Important safeguards 4Introduction 5Instruction for use

20

21How to make great espresso.This is the one method of making coffee that borders on being an art form. The better the machine you have (yes, often th

22How to texture milk.If making espresso is an art form this is like learning a craft, but once mastered it’s easy enough.The heat and texture of the

23Once you have the milk texture correct, lower the steam wand into the milk and complete the heating process.If you can hold your fingers against the

24How to clean your Giotto or Cellini.The importance of a clean espresso machine can not be under estimated when trying to produce great espresso.You

25THE GROUP.With a small hard brush, give the inside of the group a good scrub.The group should be back flushed Regularly. This means after each day,

26How to disassemble/dismantle the machineThe machine has to be disassembled and dismantled by an authorized technician.Disassembling of the machine:O

27How to disassemble/dismantle the machineSimple, routine care of your espresso machine is your best defence against poor quality shots, as well as pr

28Espresso Glossary and recipesPlease use for the following, properly ground and portioned espresso coffee. Please use app. 6, 5 to 7 grams for each s

29Trouble ShootingProblem Possible causes SolutionsLight flashing Low water level in the reservoir Add waterNo water / coffee from the group or coffee

3General dataManufacturer: Rocket Espresso Limited Viale Delle Industrie 26 20090 Settala Milano ItalyEmail: [email protected] Model:

30Problem Possible causes SolutionsPump is not running Pump is faulty Switch off and unplug machine and contact your authorized service repWater from

31(The following declaration is applicable for machines distributed in the European Community only)Declaration of CE conformityManufacturer: Rocket Es

www.rocket-espresso.com

4Important Safeguards1. Read all Instructions2. Do not touch hot surfaces. Use handle or knobs.3. To protect against electric shock do not immerse

5IntroductionPlease read this technical handbook carefully since it provides important information on the correct installation, use and maintenance of

6Instructions for useThis machine has been designed for the sole purpose of producing coffee, hot water and steam for hot beverages. All other uses ar

7All spare parts fitted to the machine must be original Rocket Espresso Ltd. components.Before any cleaning or maintenance the machine should be discon

8Description of external components1. Steam valve handle. Turn left to open steam; turn right to shut. 2. Steam wand. Can become hot and cause burn

9InstallationAll machines are designed to ensure maximum possible user safety. It is, however, an important responsibility of the user to observe the